Brass Spring Flake Adjuster and Spring Bender – Alignment & Regulator Combo For Coil Tattoo Machines
Specifications:
- Quantity: 1 adjuster
- Material: Brass
- Net Weight: 220g
- Dimension: 82.6mm x 30mm x 30mm.(L*W*H)
- Used to align your armature bar with front & back springs
- Follow directions below on bending the spring & aligning springs with armature bar
Description
Brass Alignment & Regulator Combo For Coil Tattoo Machines – Spring Flake Adjuster & Bender
This spring flake adjuster and spring bender can be used to align your armature bar with your front and back springs. It is a great tool to have in order to fine tune your machines. The adjuster & bender is made of brass and its net weight is approximately 220grams. It is 82.6mm (L) x 30mm (W) x 30mm (H). You can follow the directions below on how to bend the springs and then how to align the springs with the armature bar. Also, see the gallery of images for a detailed How-To picture for adjusting the alignment.
How to bend the springs?
- Open the spanner slightly.
- Put the front spring into the slot.
- Pull out the latch.
- Pull the latch and press the spanner in opposite directions.
- Press the spring to be bent (Please note: should not be bent more than45°)
How to align the springs and the armature bar?
- Bend the spring per instructions above. Screw on the front and back springs. Install o-ring.
- Adjust the latch position and place the armature bar & spring flake into the slot.
- Push the latch and place the armature bar & spring inside until they are in-line.
- Use the allen wrench to tighten the screw.
- Align spring, armature bar, & needle pin in a line.
- The springs & armature bar should now be aligned.
Related products
-
Snug Fit Rubber Nipples – Bag of 100 – Tattoo Supplies
0 out of 5(0)Specifications:
- Quantity: 1 bag of 100 nipples
- Material: black rubber
- Use to keep needle in place
- Lightweight and easy to use
- Manufacturer: Precision
-
Copper Front Binding Post Screw – M4 Metric – Version 1
0 out of 5(0)Specifications:
- Quantity: 1 screw
- Size: 13mm total length, 8mm for threaded area length
- Material: copper
- M4 metric
- 7mm thread length
- For front binding posts
- Manufacturer: Precision
Note :Available in version 2,6
-
Tattoo Armature Bar – 3 Choices – Baltimore Street Irons
0 out of 5(0)Specifications:
- Quantity: 1 armature bar
- 3 choices: lining bar, shading bar, or speed bar
- Size: 1 ½” long, ⅜” wide, 3/16” thick
- 8/32″ threading for mounting hole
- Black oxide treatment
- Manufacturer: Baltimore Street Irons
-
Brass Front Binding Post Screw – M4 Metric – Version 1
0 out of 5(0)Specifications:
- Quantity: 1 screw
- Size: 13mm total length, 8mm for threaded area length
- Material: brass
- M4 metric
- 7mm thread length
- For front binding posts
- Manufacturer: Precision
Note :Available in version 6,3,7,8,5
-
Specifications:
- Quantity: 1 adjuster
- Outer block size: 80mm long, 58mm wide
- Use to align armature bar with front and back springs
- Material: Aluminum
- Manufacturer: Precision
-
Armature Bar for Side by Side Coil Tattoo Machine – M4 Metric – Tattoo Machine Supplies
0 out of 5(0)Specifications:
- Quantity: 1 adjuster
- Size: 4.25” long
- Use for perfect center alignment
- Textured handle
- Easy to use
- Material: Stainless Steel
- Manufacturer: Precision
Reviews
There are no reviews yet.